Articles

How do I reset my Cisco phone adapter?

How do I reset my Cisco phone adapter?

Resetting a Cisco ATA to Factory Default

  1. Ensure that the ATA is connected to power, and connect an analog telephone into Phone 1 on the rear-panel.
  2. Take the analog phone off-hook and press the Star key four times: ****
  3. Dial the following IVR code using the phone keypad: 73738 (RESET) followed by the # key.

How do I factory reset my Cisco SPA122?

To reset the SPA122 to factory defaults follow these steps:

  1. Plug in power adapter.
  2. Plug in a phone to ‘Phone 1′ port of the SPA122.
  3. Dial ****
  4. You should hear ‘Configuration Option Menu’
  5. Dial 73738# (RESET#)
  6. Press 1 to confirm the reset.

How do I reset my Cisco 2 port phone adapter?

Press and hold for 10 seconds to restore the factory default settings. Connect to an analog phone, using an RJ-11 phone cable.

How do I factory reset my ATA?

ATA 191 and ATA 192 Top Panel

  1. System detects a factory reset. To perform a factory reset, press and hold the RESET button for about 10 seconds.
  2. A factory reset is performed successfully.

How do I program a Cisco SPA112?

Setting up the Cisco SPA112

  1. Open a web browser and enter the IP address of the phone adapter in the address bar, then press Enter.
  2. Enter the username of the device in the Username field.
  3. Enter the password of the device in the Password field.
  4. Click Login to enter the web configuration utility.

How do you reset a VOIP phone?

The following guide will help you factory reset your Cisco IP 7841 Phone….Factory Reset Cisco IP Phone 7841 (Using Keypad)

Step 1 Unplug the phone’s LAN cable.
Step 2 Wait 5 seconds.
Step 3 Press and hold # button while plugging the phone back in.
Step 4 Release the # button when the light on the handset blinks red 2 times

How do I find the IP address of my Cisco spa112?

At the voice prompt menu, enter 110 #. The phone will read back the IP address of the base, which can be entered into a browser to access the configuration. At the voice prompt menu, enter 210 #. The phone will read back the IP address of the base, which can be entered into a browser to access the configuration.

How do I find the IP address of my Cisco SPA112?

How do I make Grandstream default?

Hardware Configuration – Factory Reset – Grandstream

  1. Press the menu button (center button of the directional pad).
  2. Scroll down and select ‘System’.
  3. Scroll down and select ‘Factory Reset’.
  4. Press ‘OK’ to confirm factory reset.
  5. Press ‘OK’ to confirm to continue.
  6. Your phone will reboot.

How do I reset my Grandstream ht701?

RESET BUTTON

  1. Unplug the Ethernet cable.
  2. Locate a needle-sized hole on the back panel of the gateway unit next to the power. connection.
  3. Insert a pin in this hole, and press for about 7 seconds.
  4. Take out the pin. All unit settings are restored to factory settings.

How do I access SPA122?

Procedure

  1. Using a LAN/Ethernet cable, connect the computer to the yellow Ethernet (LAN) port of the SPA122.
  2. Open Internet Explorer browser (IE is required to ensure the adapter’s configuration page displays properly).
  3. Log in: admin / (administrator password)
  4. Click Voice > Provisioning.
  5. Click Submit.

How do I reset my PBX?

Reset the PBX

  1. Go to Maintenance > Reset.
  2. Select which data that you want to reset. Reset All: Factory reset all the data and configurations on the PBX. Reset IP: Reset the PBX’s IP address to 192.168. 5.150.
  3. Click Factory Reset.
  4. Enter the verification code.
  5. Click Reset.

What is the default password for Grandstream?

admin
The default login name for the administrator is “admin”, the default administrator password is also set to ”admin.” If you have changed the login password, you must use it to login to the web interface. In this case, if you forget the password, you can factory reset the unit to restore the default user login settings.

How do I Factory Reset my Grandstream gxp2170?

Factory Resetting the Device

  1. Go to the Menu by clicking on the round button.
  2. Go to System.
  3. Scroll down to the Operations option.
  4. Select the Factory Reset option.

How do I reset my Grandstream HT802?

Factory Reset the Device

  1. Plug in and power on the ATA device.
  2. Locate the indented RESET button between the power and ethernet port.
  3. Use a paper clip or toothpick to press and hold the reset button for 10 seconds. Do not release the button until all 4 lights on the top of the ATA flash for 1-2 seconds.

How do I access Cisco SPA112?

How to access the web configuration utility on the Cisco SPA112

  1. Open a web browser and enter the IP address of the phone adapter in the address bar, then press Enter.
  2. Enter the username of the device in the Username field.
  3. Enter the password of the device in the Password field.
  • October 21, 2022

You may also like...