How do I mix my PPG Amerlock 2 400?
Table of Contents
How do I mix my PPG Amerlock 2 400?
INSTRUCTIONS FOR USE Mixing ratio by volume 1 part base to 1 part hardener Pre-mix pigmented components with a pneumatic air mixer at moderate speeds to homogenize the container. Add hardener to base and agitate with a power mixer for 1-2 minutes until completely dispersed.
How do I use Amerlock 400?
* Amerlock 400 may be applied to surfaces as hot as 250˚ (121˚C). When applying Amerlock 400 to surfaces between 122˚F and 250˚F, thin1⁄2 pint per gallon with Amercoat 101 thinner. Multiple passes may be required to achieve film build and to avoid solvent blistering.
How do you mix Amerlock 2?
Mixing ratio by volume
- 1 part base to 1 part hardener.
- Pre-mix pigmented components with a pneumatic air mixer at moderate speeds to homogenize the container. Add hardener to base and agitate with a power mixer for 1-2 minutes until completely dispersed.
How do I thin my Amerlock 2?
Surface temperature
- 20°F to 122 °F (-6°C to 50°C)
- Amerlock 2 may be applied to surfaces as hot as 250°F (121°C) for non-immersion service.
- Amerlock 2 must be thinned at 1/2 pint per gallon with only.
- Amercoat 101 Multiple thin passes may be required to achieve film build and to avoid solvent blistering.
How do you mix amercoat 240?
Flush all equipment with thinner or Amercoat 12 before use. Stir resin using an explosion-proof power mixer to disperse into a homogeneous mixture. 2. 3….C.G.Edwards & Co.Inc.
| Components 2 | ||
|---|---|---|
| Mixing ratio (by volume) | 4 part resin to 1 part cure | |
| 6 mils (150 microns) | 233 | 5.6 |
What kind of coating is Macropoxy 646?
fast cure Epoxy Mastic
OVERVIEW. Sherwin-Williams® MACROPOXY® 646 is a fast cure Epoxy Mastic with fast dry times. It is ideal for use in protecting steel and concrete in industrial applications. It is commonly used for maintenance and painting in fabrications shop applications.
How do you mix amercoat 450h?
Mixing ratio (by volume) 4 parts resin to 1 part cure Surface temperatures must be at least 5°F (3°C) above dew point to prevent condensation. *Surface must be dry and free of all contaminants.
What is ppg amercoat?
Amercoat 68HS is a corrosion resistant zinc rich epoxy primer that protects steel substrates by sacrificing the zinc component and also insulating the steel substrate through barrier properties. Amercoat 68HS is designed to meet the needs of steel structures in coastal, high-humidity and offshore environments.
What is Macropoxy used for?
MACROPOXY 646 Fast Cure Epoxy Mastic is a high solids, high build, fast drying, polyamide epoxy designed to protect steel and concrete in industrial exposures. Ideal for maintenance painting and fabrication shop applications. The high solids content ensures adequate protection of sharp edges, corners, and welds.
Can you spray Macropoxy 646?
Sherwin-Williams® MACROPOXY® 646 can be applied by a nylon plaster blend or natural bristle brush. It can also be applied with a conventional spray gun and paint pressure pot with pressure cup as well as with an airless sprayer with a minimum of a 30:1 output ratio and that supports at least 017″-.
What is amercoat used for?
Typical Uses Specially formulated as a high performance coating for marine and industrial facilities, ballast tanks, bilges, wet voids and draining pipes, above and below water hulls.
How do you mix Macropoxy?
Sherwin-Williams® MACROPOXY® 646 is composed of two components and should be mixed by thoroughly at a low rpm with an air-powered mixer to ensure proper performance of the coating. Additionally MACROPOXY® is often combined with other coatings like Zinc and a urethane top coat.
What is Macropoxy paint?
PRODUCT DESCRIPTION. MACROPOXY 646 FAST CURE EPOXY is a high solids, high build, fast drying, polyamide epoxy designed to protect steel and concrete. in industrial exposures. Ideal for maintenance painting and fabrica-
What is Macropoxy paint used for?
It is commonly used for maintenance and painting in fabrications shop applications. It can be applied to marginally prepped steel surfaces. Common applications include refineries, fab shops, chemical plants, water treatment plants and more.
How do you mix PPG amercoat 450h?
