How do I restart APC UPS?
Table of Contents
How do I restart APC UPS?
Solution: To reset the network interface of a SMT, SMTL, or SMX model UPS, on the display interface hold the UP and DOWN buttons simultaneously for 5 seconds. The display flashes to indicate that the network interface has restarted.
How do you restart UPS?
Turn on the UPS: press and hold the On/Off button until the UPS beeps, then release the button. The green On/Off LED should now be lit. 5. Reconnect the equipment that requires battery-backup power and is within the output capacity of the UPS directly into the battery-backup/surge-protected outlets.
How do I restart my APC UPS management card?
Open your browser and enter the IP address of the APC UPS. On the login screen, use the default username and default password. After a successful login, you will be sent to the APC UPS Dashboard. Select the Reboot Management Interface and click on the Apply button.
Why UPS shuts down immediately?
Re: UPS Shut Off During Power Failure this just means to have a non critical load on the UPS, then pull the plug from AC power, and see if the UPS goes to battery. if it does, then we can investigate further on your configuration. also, please confirm you have no other USB or serial cables attached to the UPS.
Is there a reset button on a UPS?
The UPS will reset itself after a power outage. At this point there will be beeping and the UPS will be in bypass mode. o Go to the back and flip the switch to “Utility” o On the front of the UPS hold the OFF button for a second until it beeps. This will shut off the beeping and the UPS.
How do I reset apc after battery replacement?
1) Turn off and unplug the Smart-UPS from wall. Remove any attached load. 2) Press and hold the power button (labeled “”I/TEST”” on legacy non-LCD screen units) on the front of the UPS until you hear a LONG beep. 3) Let go DURING the long beep.
How do I console into apc Smart UPS?
Connect to the UPS/device serial port using the correct APC configuration cable….9600 bps, 8 data bits, no parity, 1 stop bit, and no flow control.
- Apply the port settings to establish the connection.
- Press enter 3-5 times to display the username prompt.
- Use the default username and password of “apc”.
Why does my UPS keep turning off after 5 minutes?
The Greenpower feature is activated when the total load on the UPS is equal or less than 10% of the UPS capacity, therefore if the devices connected consume less than 10% of the UPS capacity it will shut off in 5 minutes.
Why is my APC beeping?
The UPS can only operate on battery for a limited amount of time. In order to protect the unit’s batteries from discharging too much, the UPS will shutdown and turn off its output. To warn you that the unit will soon shutdown, the UPS will sound this alarm 2 minutes before actual shutdown.
Why is my UPS not working?
Be sure the line cord is connected. Be sure each circuit breaker is in the On position, or replace the fuse if needed. If this occurs repeatedly, contact an authorized service provider. Check the UPS LEDs to be sure a battery or site wiring problem has not occurred.
What to do when UPS is not turning on?
Solution:Reducing the load, then press the “”Reset”” button in. The circuit breaker is tripped if it protrudes approximately1/4″” out from the unit. Once pushed back in, try to power the unit up again. If breaker will NOT stay in, contact using its at Technical Support and have the Model and serial number available.
Is it OK to turn off UPS?
You can choose to care for your UPS battery however you see fit. But, unplugging it can result in a shorter lifespan. If you unplug your UPS each night, for example, it will self-discharge. When it is plugged in again, the battery will have to charge itself back up to “make up” for that discharge.
How do I turn off APC UPS 2200?
Press the ON/OFF button on the front panel of the UPS to power the unit and all connected equipment. 4. To use the UPS as a master on/off switch, turn on all the equipment that is connected to the UPS.
What is UPS cold start?
A cold start is when you start a UPS without input power. This is useful if you need to test if the UPS is not turning on due to bad input power or if you need to turn the UPS on to operate during a power outage/failure.
How do I find APC on my network?
Start the Network Management Card Device IP Configuration Utility. Enter the full IP address range of your network and click on the button to start the search for the UPS. The system will automatically locate the IP address of your APC UPS.
What to do if UPS is beeping?
If you’ve lost power, it’s beeping to let you know that the battery is in use, and that you should save your work and shut down your computer. A constant beep (every second or two, and never stopping) generally means the UPS is very low on battery power, and you should shut down immediately.
How do I Reboot my APC ups?
On the login screen, use the default username and default password. After a successful login, you will be sent to the APC UPS Dashboard. Select the Reboot Management Interface and click on the Apply button. In our example, the Network Management Interface will restart.
When does the ups restart in online operation?
When adequate power is restored to the UPS (and is within the operating voltage range of the UPS) it will restart in online operation. This is independent of PowerChute software being installed or not.
Why does my Smart-UPS keep restarting?
The equipment attached to a Smart-UPS can be dropped or caused to reboot due to any of the following reasons: 1) Battery issues – A UPS with a weak or failed battery may not be able to support the load attached, or may provide very brief runtimes.
Why does my ups keep going to battery and shutting off?
You may have found that your UPS has been repeatedly going to battery for very brief periods. These frequent, yet brief, periods on battery can cause the battery charge to be depleted, as the UPS never spends enough time on line to fully charge. Eventually, this will cause the UPS to shutdown.
