How thick will a hypertherm 45 cut?
Table of Contents
How thick will a hypertherm 45 cut?
Cut capacity
| Capacity | Thickness | Cut speed |
|---|---|---|
| Cutting | ||
| Recommended | 16 mm (5/8″) 22 mm (7/8″) | 500 mm/min (20 ipm) 250 mm/min (10 ipm) |
| Severance (hand cutting) | 29 mm (1-1/8″) | 125 mm/min (5 ipm) |
| Pierce* | 12 mm (1/2″) |
How many amps does a hypertherm 45 use?
Engine-driven generator operation
| Engine Drive Rating (kW) | System Output (amps) | Performance (arc stretch) |
|---|---|---|
| 8 | 45 | Full |
| 6 | 45 | Limited |
| 6 | 30 | Full |
How thick can a 45 amp plasma cutter cut?
This is the new digitally controlled 20-55 amps Plasma Cutter Machine with advanced inverter technology and high cutting performance. Designed for portable repair work and small business project use, the CUT-45M Air Plasma Cutter cuts a thickness of 2/5 in. with the max severance thickness at 3/4 in.
Where are Hypertherm Plasma Cutters made?
New Hampshire, USA
Hypertherm takes great pride in offering products that are designed and built in New Hampshire, USA. With over 40 years of metal cutting experience, their products are among the best in the world. Both the Powermax 30 XP and the 30 AIR are excellent plasma cutters.
How thick metal will a 45 amp plasma cutter cut?
5/8 inch thick
The Titanium Plasma 45 has a lot of cutting power. It cuts fast and clean, leaving a dross-free edge, except when it cuts metal over 5/8 inch thick.
How many CFM does a plasma cutter need?
These requirements differ between systems, but as an example, an air compressor for a plasma cutter like the Hypertherm Powermax45® requires 6 cubic feet per minute (cfm) at 90 psi. It is important to keep in mind that these are MINIMUM requirements.
Are Hypertherm plasma cutters good?
The Hypertherm Powermax XP tops the charts when it comes to its cutting power at 45 amps and 6.5 kw output at max power, slightly edging out the previous Powermax and the Miller Spectrum 625 X-TREME.
Do plasma cutters wear out?
Plasma cutter consumables are a set of components in your plasma cutter that gradually wear over time until they need to be replaced: they have a life cycle.
Is a plasma cutter worth it?
Plasma cutters also cut quickly and efficiently. Plasma takes one-fourth of the time of most similar techniques to make a clean break in a piece of workable metal. Fast process times also minimise the risk of metal abrasion, cuts made in error, or distortion.
Is hypertherm the best plasma cutter?
Hypertherm Powermax30 Plasma Cutter – Best Overall For our top pick, we’ve chosen the Hypertherm Powermax30 XP. It’s one of the best plasma cutters for home use, as it’s available at a low price while offering more than enough of the features a hobbyist would need.
What are 2 pros of cutting with plasma instead of oxy acetylene?
No preheating required: Because plasma doesn’t require the metal to be preheated before cutting, this saves time and money. Faster speeds on thinner metals: Plasma can cut thinner metals faster than oxy-fuel can, and with minimal or no metal distortion. Plasma also offers better performance when cutting stacked metals.
How thick can a 50 amp plasma cutter cut?
3/4 in.
Designed for portable repair work and small business project use, CUT-50 Plasma Cutter cuts a thickness of 3/4 in., and the max severance thickness is 1.0 in. Type: DC Air Plasma Cutter. Supply Power: 110-Volt/230-Volt/60Hz/1-Phase.
Can I use a regular air compressor with a plasma cutter?
All plasma manufacturers include minimum air flow and pressure requirements for an air compressor in the owner’s manual. These requirements differ between systems, but as an example, an air compressor for a plasma cutter like the Hypertherm Powermax45® requires 6 cubic feet per minute (cfm) at 90 psi.
