How do I reset my MSA 2050?

How do I reset my MSA 2050?

Restarting controllers

1. Perform one of the following: In the banner, click the system panel and select Restart System.
2. Select the Restart operation.
3. Select the controller type to restart: Management or Storage.
4. Select the controller module to restart: Controller A, Controller B, or both.
5. Click OK.
6. Click OK to continue.

How do I reset my MSA 2040 controller?

To restart the storage controller using SMU v2: Select Tools→Shut Down or Restart Controller→Operation: Restart→Controller→Type: Storage→Controller: A|B. Click Restart now. A confirmation message appears.

What is included with the MSA 2062?

Capable of delivering in excess of 325,000 IOPS, the HPE MSA 2062 saves you up to 32% with an all-inclusive software suite and 3.84 TB of flash capacity included. It’s seriously simple and affordable flash storage to help you achieve high performance yet meet challenging budgets.

How do I reset my storage controller?

1) The “reset controller” command can be run from the Storage Manager from the Enterprise Manager view (initial screen). Under the devices menu, select the subsystem where you want to reset the controllers with a single click. Then right mouse click and select the execute script button from the subsystem in question.

How do I setup my HP MSA 2050?

In Control Panel, click on MPIO, go to Discover Multi-Paths, select MSA 2050 SAN and click on Add. You will also be asked to reboot server for changes to apply – have that in mind and schedule a reboot. After Reboot if you go back to Control Panel – MPIO, you will see HPE MSA 2050 SAN on the MPIO Devices list.

How do I access HP MSA 2040?

MSA 2040 Start Up

1. Step 1: Verify Materials and Review SAN Overview.
2. Step 2: Mount the MSA to Your Rack.
3. Step 3: Install 2.5″ Hard Drives.
4. Step 4: Connect the MSA 2040 for Remote Management.
5. Step 5: Install SFP Ports on MSA and Switch (images Display Switch Only)
6. Step 6: Connecting MSA 2040 to Network Switches.

How do you turn off MSA 1050 SAN?

To power off the system:

1. Stop all I/O from hosts to the system.
2. Shut down both controllers using either method described below:
3. Disconnect the power cord female plug from the power cord connector on the power supply module.

How do I turn off HPE storage?

To shut the storage system down, perform the following steps:

1. Start HP Command View EVA.
2. Select the appropriate storage system in the Navigation pane.
3. Click System options.
4. Click Shut down.
5. Under System Shutdown click Power Down.
6. Turn off the power switch on the rear of each HSV controller.

How do I reset my MSA account?

Reset the manage user to manage access level with the following command:

1. # set user manage level manage type diagnostic interfaces cli,wbi,ftp.
2. Info: Access-level set to manage.
3. Success: User-Type set to diagnostic.
4. # set password manage.
5. Enter new password:******* <<<—- password set to !

How do I find my gMSA ad account?

To check it, Go to → Server Manager → Tools → Active Directory Users and Computers → Managed Service Accounts. The result should come “True” after running the second command, as shown in the screenshot given below. Step 4 − Go to service properties, specify that the service will be run with a gMSA account.

How do I add a host to my MSA 2040?

Add Host in MSA 2040 SAN

1. First, find the host’s WWN or IQN.
2. Login to HPE Storage Management Utility (SMU) by using credentials, default username/password are manage/!
3. In the Configuration View panel, right-click the system or Hosts and then select Provisioning >> Add Host.

How do I connect to MSA 2050?

To connect the MSA 2050 array to a remote management host, connect an RJ-45 Ethernet cable from theEthernet network management port on each MSA 2050 controller to a switch that users management host canaccess (Preferably on the same subnet).