What does matric suction mean?
Table of Contents
What does matric suction mean?
Matric suction or negative matric potential (unit: kilopascal) is the free energy change in a unit volume of water when isothermally transferred from the soil water state to the free water state, and is defined at the soil-water-air representative elementary volume (REV) [Fig. 1(a)].
Is pore water pressure good?
Effective stress, negative pore pressure and suction Below the water table, pore pressure is positive; in dry soils and at the level of the water table, pore pressure is zero; above the water table, soil can remain saturated due to capillary rise but with negative pore pressure (suction).
What is soil suction?
Soil suction is defined as the state of the soil when it is under reduced pressure. It is measured in terms of the height of the water column (h) suspended in the soil. The main features and factors affecting soil suction are explained briefly.
How do you measure pore water pressure in soil?
Under hydrostatic conditions (no water flow) the pore pressure at a given point is given by the hydrostatic pressure: u = gw . h. It is convenient to think of pore pressure represented by the column of water in an imaginary standpipe; the pressure just outside being equal to that inside.
How is matric suction calculated?
In the case of unsaturated soil, pore water pressure will be equalized to matric suction and the hydraulic head will become H=z+(ua-uw)/γw. By introducing these terms in Darcy law, (4) was obtained the differential equation of matric suction in relation to z (the distance of a point from unsaturated zone to GWT).
What is pore pressure ratio?
The pore pressure ratio Ru has been used for many years as a parameter to represent the global pore water pressure condition in a slope stability analysis. Today, the use of computer programs has often removed the need for chart-based or coefficient-based methods of slope stability analysis using Ru.
What is a negative pore pressure?
Negative pore pressure: it is water pressure from the outer surface or from below the concrete or pressure due to the ground is meant developed is known as negative water or negative power pressure.
How do you measure soil suction?
The soil suction will then manifest itself in the reservoir as a tensile stress in the water and can be measured by the stress measuring instrument, e.g. a manometer, a vacuum gauge or an electric pressure sensor. In this way tensiometers measure porewater tensions or negative porewater pressures.
What is suction in engineering?
Suction is the colloquial term to describe the air pressure differential between areas. Removing air from a space results in a pressure differential. Suction pressure is therefore limited by external air pressure.
What is soil matric potential?
Soil matric potential (SMP) represents the relative availability of the amount of water held in the soil profile for plant uptake/use. SMP indicates how much energy plants will have to exert to extract the water molecules from soil particles.
What is soil suction head?
The suction head, represented in millimeters, is the capillary attraction on the soil voids. It is large for fine grain soils such as clays and smaller for sandy soils.
How does a tensiometer work?
The tensiometer acts like a root, whereas its ceramic tip interacts with the soil, emitting water when it is dry. When the water leaves the tube, a measurable pressure is generated and displayed on a gauge attached to the top of the instrument.
What is the advantage of a tensiometer?
Tensiometers can be helpful in determining how much moisture has actually penetrated and how quickly. Tensiometers are best used when soil moisture will be maintained at 50 to 75 percent of field capacity such as in high moisture demand crops like corn or vegetables.
What is RU value?
The Ru ratio is a crude way of describing pore-water conditions in a slope stability analysis. A single Ru value can seldom, if ever, represent the actual field groundwater flow conditions. Although it is rarely used in practice, Ru remains an option in SLOPE/W for legacy reasons.
How is excess pore pressure calculated?
Excess pore pressure from yielding can now be simply calculated as the horizontal difference of the intersection of K0-line with the initial yield surface, and the intersection of the failure line with the yield surface in the (p’, q) stress space. For this a proper estimation of the yield surface is needed.
What is suction head of soil?