What is the difference between 6011 and 6013?
Table of Contents
What is the difference between 6011 and 6013?
The 6011 is used mainly for welding mild steel and rusted, painted, or dirty surfaces. On the other hand, the 6013 is primarily used for welding thin sheets of metals. The 6013 is used in applications that require low amperage, while the 6011 is used where high penetration is needed.
What is a 6011 rod used for?
E 6011 electrode is a general-purpose electrode performs welding in all positions and efficiently in vertical-up and over-head positions; it is used mainly for sheet metal welding and low silicon deposit application. The electrode arc is easy to control and produces a flat weld bead with light slag formation.
What is a 6011 Rod What makes it different?
The 6011 welding rod is useful for jobs that require deep penetration, no matter the position or welder setup. It is a solid all-around welding rod. Because it is an iron rod, it is useful for most kinds of iron and mild steel. You can handle just about anything with 6011 rods.
Is 6013 good for rusty metal?
What are 6013 rods used for? Because these electrodes have a moderate burning arc, they don’t penetrate as deeply as other electrodes. That’s why they should be used for clean, thin sheet metal.
What does E6011 mean in welding?
Here are some of the most common welding rods. E6010 – an all-position rod especially used in pipe welding, known for its tight arc. E6011 – all-position rod that is a preferred choice for maintenance work, or where metal is rusted and/or dirty.
Can you use 6011 on DC?
While the 6011 was specifically designed for AC machines, it can also run on DC giving it an advantage over the 6010 electrodes (which can only do Direct Current Electrode Positive).
Can you weld stainless with a 6011 Rod?
I’ve used 6011/6013 rods in a few instances that the weld didn’t need to be stainless or pretty. Had a guy I worked with used to surface ripper points with 6011, but it’s not ideal. You can weld most stainless with mild steel wire or rod, the welds will be softer than the steel and will rust.
Can you run 6011 on DC?
How many amps does a 6011 welding rod need?
Product has a stable arc with low spatter levels. Amperage Range: Minimum: 60 amps. Maximum: 90 amps.
How many amps is a 6011 Rod?
6011 (blue spot)
| Diameter | Flat amps | Overhead amps |
|---|---|---|
| 1/8 | 90 140 | 80 130 |
| 5/32 | 110 160 | 120 150 |
| 3/16 | 160 195 | 140 – 180 |
| 7/32 | 190 250 |
Should I run 6011 on AC or DC?
While the 6011 was specifically designed for AC machines, it can also run on DC giving it an advantage over the 6010 electrodes (which can only do Direct Current Electrode Positive). A common mistake for Stick welders is to treat their 6013 electrodes like 6011 or 6010 rods.
What amp do I need to weld 6011?
Can you use 6013 to weld stainless steel?
You can use 6013, depending on your welders capacity. It’s much like 6011 which i’ve used on SS before.
What does E6011 stand for?
E6011 (E4311) electrode is meant for mild steel welding. The meaning of the E6011 (E4311) electrode is: E Means Electrode for stick welding, 60 mean 60 Ksi electrode tensile strength. 1 at third digit means the welding electrode to be used for all positions.
Can you weld vertical down with 6011?
6011 rods weld all positions and all directions… uphill and downhill both can be done…downhill welding is no problem…. sometimes, when you weld with downhill with 6013 rods slag runs ahead of the puddle and causes problems like slag inclusions and wormholes.
What amp do I need for 6013?
6013 Tensile strength is 60,000 PSI Amperage 40-80 Amps AC, DCEN, DCEP (Either Polarity).
What is the difference between 6011 and 6013 welding rods?
The 6011 welding rod lengthens by 24%, whereas the 6013 welding rod lengthens by 25% in 2 inches. As mentioned, both rods have a minimum tensile strength of 60,000 pounds per square inch. Maximum tensile strength, however, varies significantly between the two.
What is the difference between 6013 and 6011 slag?
The 6013 has a soft arc, dense slag similar to 7018, and is more of a drag rod, while 6011 has a more violent arc, slag is flaky and you can manipulate the arc more by whipping it.
What is the tensile strength of 6011 and 6013 electrodes?
In both of the electrodes (6011 and 6013), 60 is the number we use. Hence, both electrodes have a maximum tensile strength of 60,000 psi. Despite the similarity of some properties on their application, there exist differences between the two; #1. Penetration
