What is the margin of safety on a saw?
Table of Contents
What is the margin of safety on a saw?
Between 1/4 – 3/8”. Don’t reach over or behind the table saw blade. Never position your hands or fingers in the path of the table saw blade. Keep a 4-6” margin of safety all the way around your table saw blade.
What are the safety measures of saw?
Wear safety glasses or goggles, or a face shield (with safety glasses or goggles). Wear an approved respirator or dust mask when exposed to harmful or nuisance dusts. Use appropriate hearing protection equipment in noisy areas. Check the retracting lower blade guard to make certain it works freely.
What are 3 safety rules for a table saw?
Safety Rules Safety glasses and hearing protection are required. Never saw freehand. Never clear small pieces while blade is moving. Never adjust saw or setup while saw is running.
What are the safety operations of a table saw?
Keep the body and face to one side of the saw blade out of the line of a possible kickback. Provide adequate support to the rear and sides of a saw table for wide or long stock. Be careful when waxing, cleaning, or servicing the table. Turn off the power and unplug (or lock out) a saw before doing any work on the saw.
What is the number 1 safety rule of the band saw?
Never push on back of piece with fingers or thumb. Don’t reach across the blade. Make all cuts under power, not while blade is coasting. Never remove guard unless authorized by Technician or WRL Manager.
What is the minimum length of stock that should be cut on a table saw?
Wood Shop Safety Rules
| A | B |
|---|---|
| Table Saw | Never “free hand” |
| Table Saw | Only let 1/4″ extrude above board |
| Table Saw | Always use a push stick |
| Table Saw | Minimum stock length is 12″ |
Are miter saws safe?
Mitre saws can be dangerous if not used properly. Read the owner’s manual carefully. Make sure you know and understand the instructions before attempting to use any tool or machine. Learn the applications and limitations before use.
What is the minimum length you should cut on a table saw?
Avoid working with short pieces of wood whenever possible. Plan ahead and don’t cut your boards Page 5 too short too soon. A minimum length of 12″ is a good standard to use. 18.
What is the margin of safety on the jointer?
Keep your hands away from the cutterhead even through the guard is in position. Maintain at least a 6” margin of Safety!!! 9.
What are 5 general guidelines for using the band saw?
Safety Rules Safety glasses are required. Never clear small pieces while blade is moving. Never adjust saw or setup while saw is running. Never cross arms.
How far should the safety guard be above the stock?
5. Keep safety guards in place. Upper guide should clear stock by about 6 mm (1/4”).
What is the minimum length of stock that should be cut on the radial arm saw?
Wood Shop Safety Rules
| A | B |
|---|---|
| Table Saw | Minimum stock length is 12″ |
| Radial Arm Saw | Observe a 6″ safety margin |
| Radial Arm Saw | Blade only lowered 1/16″ below board |
| Radial Arm Saw | Only cross cut boards |
What is the maximum distance the rip fence can safely be set from the saw blade?
Never allow the hands to come closer than 12 inches to the saw blade. Position the right hand so it is NOT in direct line with the saw blade. Remove the hand holding the stock down as it approaches the saw blade guard. For narrow ripping cuts, where a push stick cannot be used, use a push block or an auxiliary fence.
What are some general OSHA guidelines when using power tools?
Power Tools
- Never carry a tool by the cord.
- Never yank the cord to disconnect it from the receptacle.
- Keep cords away from heat, oil, and sharp edges (including the cutting surface of a power saw or drill).
- Disconnect tools when not in use, before servicing, and when changing accessories such as blades, bits, etc.
What are some safety tips when using a miter saw?
What safety precautions should you follow when using a mitre saw?
- Wear safety glasses or goggles, or a face shield (with safety glasses or goggles).
- If work is dusty, use a dust extraction system, and/or respirator or dust mask.
- Wear appropriate hearing protection.
- Wear protective footwear when required.
Is it safe to use a miter saw on the ground?
It is not recommended for you to use a miter saw on the floor. Although it is possible but it may be challenging to hold the board you are cutting level and in place. You can always buy or build a miter saw stand so you won’t have a hard time to work with your miter saw on the floor.
When must you use a miter gauge when using a table saw?
Can a table saw make miter cuts? The blade can usually be tilted up to 45 degrees to cut angles on the edges of a board, but this kind of cut is called a bevel, not a miter. You’ll need to add a miter gauge to cut the proper angle for a miter with the saw blade in the upright position.
